How To Properly Measure Your Penis Before Buying A Cock Cage

charlaf7 | December 3, 2018 | 0 | News

Sharing is caring!

PROPER MEASUREMENTS AND FITTING


 

The goal for a perfectly fitting cage is…

 

  • (A) THE RING SECTION should fit around your scrotum and penis base snug enough that it won’t slip off – that’s it. You’re NOT aiming for cock and ball torture – this is chastity play. Too loose and it won’t stay on. Too tight and you could run into circulation problems.

 

  • (B) THE PENIS LENGTH should accommodate your penis enough that the tip JUST presses on the end of the cage (with no compression). Too short, and it will cause unnecessary discomfort. Too long and you have room to get an erection (and any night time wood might be painful) Also, urination will be a disaster. In the end, we’re sure you don’t want small chastity cage for big penis.

 

  • (C) THE PENIS DIAMETER should house your (flaccid) penis comfortably. Too tight, and any movement will cause the skin to bunch or bulge out of any open spaces, causing chafing and discomfort. Too loose, and you’ll have room to get an erection.

 

How to measure you cock for a chastity cage

 

In short, you’re aiming for the GOLDIE LOCKS ZONE – not too tight and not too lose.

 

 

(A) FITTING THE RING

 

Fair warning, this is the most difficult number to get, and it will take the most time and effort.

 

Also, it will be tempting to skip this part, get something “close enough”, and jump straight to chastity play. But I strongly advise you NOT to do that. Even if you’re going for something casual, an ill-fitting cage (even by a little) will result in discomfort

 

FIRST – Use a soft measuring tape to measure around your scrotum and penis. Use this number (let’s call it “IM” – initial measurement) as a rough guide for the next step…

 

NOTE: DO THIS WHILE YOU’RE 100% FLACCID – Gentlemen, you know how the slightest touch or even looking at your dick can get you hard. So, if you feel things growing, make sure you take breaks and get back to completely soft.

 

Penis rings, black cock ringsSECOND – You have two choices – buying a cheap cock ring set online OR buying metal rings from the hardware store.

 

If you go for the cock rings, make sure your IM is found in the set somewhere (preferably in the middle). If you’re going to the hardware store, get a ring that’s closest to your IM and then buy two or three rings bigger and smaller in ¼ inch (6mm) increments.

 

THIRD – Get your IM ring and put it around your (flaccid) penis and scrotum (read “Getting into Your Cage” section below to learn how).

 

FOURTH – Try to stick your finger between the ring and your penis. If it’s a tight fight, you’re good to go to the next step. If you can’t fit it in, move up one size. If there’s too much room, go down one size. Do this until you find a good one.

 

FIFTH – Once you have your candidate, put it on and leave it on. Walk around the house, go to work, wear it to bed, wear it in the shower, try it in hot or cold temperatures. Do this for a few days and adjust to smaller or bigger sizes if necessary.

 

The goal is to be able to wear this ring for several days without any discomfort. If you can do this, you have a winner.

 

NOTE: Some men might find that the can’t fit between Ring A and Ring B, even with ¼ inch differences. If that’s the case, you’re in between and would need to adjust to 1/8 of an inch difference. Some cock cage makers will happily do this. The mass-produced ones will be harder.

 

 

(B) FITTING THE PENIS (LENGTH)

 

This one is still tricky but WAY easier than getting your ring number.

 

All you need is a ruler.

 

Measuring under the penis, rest the tip of the ruler against the scrotum. DON’T PRESS, just let it touch. Take the number where the tip of your penis ends.

 

However, there are some things to keep in mind…

 

  • Like before, you must be 100% flaccid – not the start of an erection and not in turtle mode when you’re cold

 

  • Men want to show off how big their dicks are. Because of this, many gents try to get a bigger number, resulting in a bad fitting cage

 

  • Take several measurements at different times of the day. You’ll eventually find your average number

 

  • When in doubt, go shorter! (like ¼ or ½ an inch / 0.6 – 1.3cm)

 

 

(C) FITTING THE PENIS (DIAMETER)

 

Although this is the “least vital” of your three numbers, it’s still a good idea to get something that fits. Because too big or too small also has problems (that we’ve already touched on).

 

FIRST – Place your flaccid penis on the ruler and measure the diameter (how wide).

 

SECOND – Subtract about ½ an inch (or 1.3cm) to make sure it’s “snug”.

 

NOTE: If you want an approximate circumference measurement, multiply the diameter by 3.14 (pi). After, measure around your penis with a soft measuring tape and compare the numbers to get an average.

Related Posts

shares